New Found Intercepts 41 g/t Au Over 8.7m & 33 g/t Au Over 6.7m, Extends Iceberg Strike Length To 665m

VANCOUVER, British Columbia--(BUSINESS WIRE)-- New Found Gold Corp. (“New Found” or the “Company”) (TSX-V: NFG, NYSE-A: NFGC) is pleased to announce the results from 10 diamond drill holes that were completed as part of a follow-up drill program at the new Iceberg discovery, a high-grade zone located 300m northeast of Keats Main along the highly prospective Appleton Fault Zone (“AFZ”). New Found’s 100%-owned Queensway project comprises a 1,662km² area, accessible via the Trans-Canada Highway, 15km west of Gander, Newfoundland and Labrador.

Figure 1: Photos of mineralization: Top Left: at ~ 20.4m from NFGC-23-1264, Top Right: at ~ 21.0m from NFGC-23-1264, Bottom Left: at ~216.9 from NFGC-23-1232, Bottom Right: at ~43.1m from NFGC-23-1248. ^Note that these photos are not intended to be representative of gold mineralization in NFGC-23-1232, NFGC-23-1248 and NFGC-23-1264. (Photo: Business Wire)

Iceberg Highlights:

Hole No.	From (m)	To (m)	Interval (m)1	Au (g/t)	Zone
NFGC-23-1264	20.00	26.70	6.70	33.28	Iceberg
Including	20.00	21.90	1.90	85.35
Including	22.65	23.30	0.65	80.80
NFGC-23-1286	77.60	86.30	8.70	40.55	Iceberg
Including	79.55	81.40	1.85	176.00
Including	83.50	84.20	0.70	15.45

Table 1: Iceberg Drilling Highlights

¹Note that the host structures are interpreted to be steeply dipping and true widths are generally estimated to be 70% to 95% of reported intervals. Infill veining in secondary structures with multiple orientations crosscutting the primary host structures are commonly observed in drill core which could result in additional uncertainty in true width. Composite intervals reported carry a minimum weighted average of 1 g/t Au diluted over a minimum core length of 2m with a maximum of 4m consecutive dilution. Included high-grade intercepts are reported as any consecutive interval with grades greater than 10 g/t Au. Grades have not been capped in the averaging and intervals are reported as drill thickness.

• 40.6 g/t Au over 8.70m in NFGC-23-1286 and 33.3 g/t Au over 6.70m in NFGC-23-1264 occur at or just below surface and are located 50m along strike to the northeast of previously released 105 g/t Au over 27.05m in NFGC-23-1210 (June 5, 2023). These results expand the high-grade segment of the Keats-Baseline Fault Zone (“KBFZ”) at Iceberg and continue to demonstrate strong continuity of high-grade gold mineralization (Figures 1-4).

• Continued step-out drilling at Iceberg East has intercepted 4.66 g/t Au over 2.70m in NFGC-23-1307, representing the furthest east intercept received to date into the KBFZ. This intercept is located 100m along strike of previously reported highlight interval 21.7 g/t Au over 4.55m in NFGC-23-1285 and expands the Iceberg-Iceberg East segment to 665m while increasing the total mineralized KBFZ (Keats-Iceberg-Iceberg East) corridor to 1.9km in strike length.

• Iceberg-Iceberg East is interpreted to be the fault-displaced eastern extension of the Keats Main Zone that is hosted by the KBFZ. This new discovery remains open in all directions and drilling is ongoing to expand along strike and to depth with several intervals currently pending assay results.

Greg Matheson, Chief Operating Officer of New Found, stated: “Seeing high-grade intercepts consistently along strike with widths ranging from 5-20m+ is a pleasant déjà vu moment, taking me back to early drilling at Keats Main. There is much to be learned about the Keats-Baseline Fault Zone and we look forward to continued exploration in this highly prospective corridor.”

Drillhole Details

Hole No.	From (m)	To (m)	Interval (m)	Au (g/t)	Zone
NFGC-23-12321	209.00	217.70	8.70	3.09	Iceberg
Including	209.85	210.75	0.90	14.15
And2	252.90	255.30	2.40	1.53
NFGC-23-12483	40.30	43.05	2.75	1.18	Iceberg
And1	67.25	70.60	3.35	1.77
And3	96.80	99.50	2.70	4.53
Including3	96.80	97.50	0.70	13.30
And3	103.50	105.80	2.30	1.36
NFGC-23-1251	No Significant Values				Iceberg
NFGC-23-12551	45.00	47.00	2.00	1.67	Iceberg
NFGC-23-12641	20.00	26.70	6.70	33.28	Iceberg
Including	20.00	21.90	1.90	85.35
Including	22.65	23.30	0.65	80.80
NFGC-23-12861	77.60	86.30	8.70	40.55	Iceberg
Including	79.55	81.40	1.85	176.00
Including	83.50	84.20	0.70	15.45
NFGC-23-12951	125.50	127.80	2.30	1.14	Iceberg East
NFGC-23-13011	24.70	26.75	2.05	1.88	Iceberg East
NFGC-23-13071	121.30	124.00	2.70	4.66	Iceberg East
Including1	121.30	121.75	0.45	26.76
NFGC-23-1324	No Significant Values				Iceberg East

Table 2: Summary of composite results reported in this press release for Iceberg and Iceberg East

Note that the host structures are interpreted to be steeply dipping and true widths are generally estimated to be ¹70% to 95% and ²40% to 70% of reported intervals. ³True widths are unknown that this time. Infill veining in secondary structures with multiple orientations crosscutting the primary host structures are commonly observed in drill core which could result in additional uncertainty in true width. Composite intervals reported carry a minimum weighted average of 1 g/t Au diluted over a minimum core length of 2m with a maximum of 4m consecutive dilution. Included high-grade intercepts are reported as any consecutive interval with grades greater than 10 g/t Au. Grades have not been capped in the averaging and intervals are reported as drill thickness.

Hole No.	Azimuth (°)	Dip (°)	Length (m)	UTM E	UTM N	Prospect
NFGC-23-1232	300	-45	287	658463	5427726	Iceberg
NFGC-23-1248	299	-45.5	287	658509	5427815	Iceberg
NFGC-23-1251	299	-45.5	323	658484	5427684	Iceberg
NFGC-23-1255	299	-45.5	263	658510	5427844	Iceberg
NFGC-23-1264	299	-45.5	203	658488	5427856	Iceberg
NFGC-23-1286	300	-45	302	658531	5427831	Iceberg
NFGC-23-1295	299	-45.5	302	658841	5428028	Iceberg East
NFGC-23-1301	299	-45.5	233	658757	5428076	Iceberg East
NFGC-23-1307	299	-45.5	304	658890	5428115	Iceberg East
NFGC-23-1324	300	-45	275	659214	5428274	Iceberg East

Table 3: Details of drill holes reported in this press release

Queensway 500,000m Drill Program Update

The Company is currently undertaking a 500,000m drill program at Queensway and approximately 59,250m of core is currently pending assay results.

Sampling, Sub-sampling, and Laboratory

All drilling recovers HQ core. Drill core is split in half using a diamond saw or a hydraulic splitter for rare intersections with incompetent core.

A geologist examines the drill core and marks out the intervals to be sampled and the cutting line. Sample lengths are mostly 1.0 metre and adjusted to respect lithological and/or mineralogical contacts and isolate narrow (<1.0m) veins or other structures that may yield higher grades.

Technicians saw the core along the defined cutting line. One-half of the core is kept as a witness sample and the other half is submitted for analysis. Individual sample bags are sealed and placed into totes, sealed and marked with the contents.

New Found has submitted samples for gold determination by fire assay to ALS Canada Ltd. (“ALS”) and by photon assay to MSALABS (“MSA”) since June 2022. ALS and MSA operate under a commercial contract with New Found.

Drill core samples are shipped to ALS for sample preparation in Sudbury, Ontario, Thunder Bay, Ontario, or Moncton, New Brunswick. ALS is an ISO-17025 accredited laboratory for the fire assay method.

Drill core samples are also submitted to MSA in Val-d’Or, Quebec. MSA operates numerous laboratories worldwide and maintains ISO-17025 accreditation for many metal determination methods. Accreditation of the photon assay method at the MSA Val D’Or laboratory is in progress.

At ALS, the entire sample is crushed to approximately 70% passing 2mm. A 3,000-g split is pulverized. “Routine” samples do not have visible gold (VG) identified and are not within a mineralized zone. Routine samples are assayed for gold by 30-g fire assay with an inductively-couple plasma spectrometry (ICP) finish. If the initial 30-g fire assay gold result is over 1 g/t, the remainder of the 3,000-g split is screened at 106 microns for screened metallics assay. For the screened metallics assay, the entire coarse fraction (sized greater than 106 microns) is fire assayed and two splits of the fine fraction (sized less than 106 microns) are fire assayed. The three assays are combined on a weight-averaged basis. Samples that have VG identified or fall within a mineralized interval are automatically submitted for screened metallic assay for gold.

At MSA, the entire sample is crushed to approximately 70% passing 2mm. For “routine” samples that do not have VG identified and are not within a mineralized zone, the samples are riffle split to fill two 450g jars for photon assay. The assays reported from both jars are combined on a weight-averaged basis. If one of the jars assays greater than 1 g/t, the remaining crushed material is weighed into multiple jars and are submitted for photon assay.

For samples that have VG identified or are within a mineralized zone, the entire crushed sample is weighed into multiple jars and are submitted for photon assay. The assays from all jars are combined on a weight-averaged basis.

All samples prepared at ALS or MSA are also analyzed for a multi-element ICP package (ALS method code ME-ICP61) at ALS Vancouver.

Drill program design, Quality Assurance/Quality Control and interpretation of results are performed by qualified persons employing a rigorous Quality Assurance/Quality Control program consistent with industry best practices. Standards and blanks account for a minimum of 10% of the samples in addition to the laboratory’s internal quality assurance programs.

Quality Control data are evaluated on receipt from the laboratories for failures. Appropriate action is taken if assay results for standards and blanks fall outside allowed tolerances. All results stated have passed New Found’s quality control protocols.

New Found’s quality control program also includes submission of the second half of the core for approximately 5% of the drilled intervals. In addition, approximately 1% of sample pulps for mineralized samples are submitted for re-analysis to a second ISO-accredited laboratory for check assays.

The Company does not recognize any factors of drilling, sampling or recovery that could materially affect the accuracy or reliability of the assay data disclosed.

The assay data disclosed in this news release have been verified by the Company’s Qualified Person against the original assay certificates.

The Company notes that it has not completed any economic evaluations of its Queensway Project and that the Queensway Project does not have any resources or reserves.

Qualified Person

The scientific and technical information disclosed in this press release was reviewed and approved by Greg Matheson, P. Geo., Chief Operating Officer, and a Qualified Person as defined under National Instrument 43-101. Mr. Matheson consents to the publication of this press release dated June 15, 2023, by New Found. Mr. Matheson certifies that this press release fairly and accurately represents the scientific and technical information that forms the basis for this press release.

About New Found Gold Corp.

New Found holds a 100% interest in the Queensway Project, located 15km west of Gander, Newfoundland and Labrador, and just 18km from Gander International Airport. The project is intersected by the Trans-Canada Highway and has logging roads crosscutting the project, high voltage electric power lines running through the project area, and easy access to a highly skilled workforce. The Company is currently undertaking a 500,000m drill program at Queensway and is well funded for this program with cash and marketable securities of approximately $52 million as of June 2023.

Please see the Company’s website at www.newfoundgold.ca and the Company’s SEDAR profile at www.sedar.com.

Acknowledgements

New Found acknowledges the financial support of the Junior Exploration Assistance Program, Department of Natural Resources, Government of Newfoundland and Labrador.

Contact

To contact the Company, please visit the Company’s website, www.newfoundgold.ca, and make your request through our investor inquiry form. Our management has a pledge to be in touch with any investor inquiries within 24 hours.

New Found Gold Corp.
Per: “Collin Kettell”
Collin Kettell, Chief Executive Officer
Email: ckettell@newfoundgold.ca
{Phone: +1 (845) 535-1486

Neither the TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in the policies of the TSX Venture Exchange) accepts responsibility for the adequacy or accuracy of this release.

Forward-Looking Statement Cautions

This press release contains certain “forward-looking statements” within the meaning of Canadian securities legislation, relating to exploration, drilling and mineralization on the Company’s Queensway gold project in Newfoundland and Labrador; assay results; the interpretation of drilling and assay results, the results of the drilling program, mineralization and the discovery of zones of high-grade gold mineralization; plans for future exploration and drilling and the timing of same; the merits of the Queensway project; future press releases by the Company; and funding of the drilling program. Although the Company believes that such statements are reasonable, it can give no assurance that such expectations will prove to be correct. Forward-looking statements are statements that are not historical facts; they are generally, but not always, identified by the words “expects”, “plans”, “anticipates”, “believes”, “interpreted”, “intends”, “estimates”, “projects”, “aims”, “suggests”, “indicate”, “often”, “target”, “future”, “likely”, “pending”, “potential”, “goal”, “objective”, “prospective”, “possibly”, “preliminary”, and similar expressions, or that events or conditions “will”, “would”, “may”, “can”, “could” or “should” occur, or are those statements, which, by their nature, refer to future events. The Company cautions that forward-looking statements are based on the beliefs, estimates and opinions of the Company's management on the date the statements are made, and they involve a number of risks and uncertainties. Consequently, there can be no assurances that such statements will prove to be accurate and actual results and future events could differ materially from those anticipated in such statements. Except to the extent required by applicable securities laws and the policies of the TSX Venture Exchange, the Company undertakes no obligation to update these forward-looking statements if management's beliefs, estimates or opinions, or other factors, should change. Factors that could cause future results to differ materially from those anticipated in these forward-looking statements include risks associated with possible accidents and other risks associated with mineral exploration operations, the risk that the Company will encounter unanticipated geological factors, risks associated with the interpretation of assay results and the drilling program, the possibility that the Company may not be able to secure permitting and other governmental clearances necessary to carry out the Company's exploration plans, the risk that the Company will not be able to raise sufficient funds to carry out its business plans, and the risk of political uncertainties and regulatory or legal changes that might interfere with the Company's business and prospects. The reader is urged to refer to the Company's Annual Information Form and Management’s discussion and Analysis, publicly available through the Canadian Securities Administrators' System for Electronic Document Analysis and Retrieval (SEDAR) at www.sedar.com for a more complete discussion of such risk factors and their potential effects.

View source version on businesswire.com: https://www.businesswire.com/news/home/20230615277729/en/

New Found Gold Corp.

Per: “Collin Kettell”

Collin Kettell, Chief Executive Officer

Email: ckettell@newfoundgold.ca

Phone: +1 (845) 535-1486

Source: New Found Gold Corp.