DLP Resources intersects 339.35m of 0.76% CuEq* within a 1058.35m interval of 0.38% CuEq*, on the Aurora Project
DLP Resources has announced significant drill results from hole A24-020 at its Aurora copper-molybdenum-silver project in southern Peru. The drillhole, located 135m southeast of A24-016, intersected notable mineralization including 0.76% CuEq over 339.35m within a broader interval of 0.38% CuEq over 1058.35m. The hole was drilled from September to October 2024, reaching a depth of 1061.35m where it was stopped due to drill rig capacity limitations. The company plans to complete an initial resource estimation by March 2025.
DLP Resources ha annunciato risultati significativi di perforazione dal foro A24-020 presso il suo progetto di rame-molibdeno-argento Aurora nel sud del Peru. Il foro di perforazione, situato a 135 metri a sud-est di A24-016, ha incrociato una notevole mineralizzazione che include 0,76% CuEq su 339,35 m all'interno di un intervallo più ampio di 0,38% CuEq su 1058,35 m. Il foro è stato perforato da settembre a ottobre 2024, raggiungendo una profondità di 1061,35 m dove è stato arrestato a causa delle limitazioni di capacità dell'impianto di perforazione. L'azienda prevede di completare una stima iniziale delle risorse entro marzo 2025.
DLP Resources ha anunciado resultados de perforación significativos del pozo A24-020 en su proyecto de cobre-molibdeno-plata Aurora en el sur de Perú. El pozo de perforación, ubicado a 135 m al sureste de A24-016, intersectó mineralización notable que incluye 0,76% CuEq sobre 339,35 m dentro de un intervalo más amplio de 0,38% CuEq sobre 1058,35 m. La perforación se realizó de septiembre a octubre de 2024, alcanzando una profundidad de 1061,35 m donde se detuvo debido a limitaciones de capacidad de la plataforma de perforación. La empresa planea completar una estimación inicial de recursos para marzo de 2025.
DLP Resources는 페루 남부의 오로라 구리-몰리브덴-은 프로젝트에서 A24-020 구멍의 중요한 드릴 결과를 발표했습니다. 드릴홀은 A24-016의 남동쪽으로 135m 떨어진 곳에 위치하며, 339.35m에서 0.76% CuEq를 포함한 주목할 만한 광물화를 교차했습니다. 이 구멍은 2024년 9월부터 10월까지 드릴링되었으며, 드릴링 기계의 용량 제한으로 인해 1061.35m의 깊이에 도달하여 중단되었습니다. 회사는 2025년 3월까지 초기 자원 추정을 완료할 계획입니다.
DLP Resources a annoncé des résultats de forage significatifs du trou A24-020 dans son projet de cuivre-molybdène-argent Aurora dans le sud du Pérou. Le trou de forage, situé à 135 m au sud-est de A24-016, a rencontré une minéralisation notable, y compris 0,76% CuEq sur 339,35 m dans un intervalle plus large de 0,38% CuEq sur 1058,35 m. Le forage a été réalisé de septembre à octobre 2024, atteignant une profondeur de 1061,35 m où il a été arrêté en raison de limitations de capacité de l'équipement de forage. La société prévoit de compléter une estimation initiale des ressources d'ici mars 2025.
DLP Resources hat bedeutende Bohrergebnisse aus der Bohrung A24-020 seines Aurora Kupfer-Molybdän-Silberprojekts im Süden Perus bekannt gegeben. Die Bohrung, die sich 135 m südöstlich von A24-016 befindet, schnitt bemerkenswerte Mineralisierungen, darunter 0,76% CuEq über 339,35 m innerhalb eines breiteren Intervalls von 0,38% CuEq über 1058,35 m. Die Bohrung wurde von September bis Oktober 2024 durchgeführt und erreichte eine Tiefe von 1061,35 m, wo sie aufgrund von Kapazitätsbeschränkungen der Bohranlage gestoppt wurde. Das Unternehmen plant, bis März 2025 eine erste Ressourcenschätzung abzuschließen.
- Significant copper equivalent grades: 0.76% CuEq over 339.35m
- Extensive mineralization from surface to end of hole (1058.35m)
- Initial resource estimation planned for March 2025
- Consistent mineralization found in all 20 drillholes to date
- Drilling stopped prematurely due to rig capacity limitations
- Some intervals showed low core recovery (35-43%) due to fractured rock
Cranbrook, British Columbia--(Newsfile Corp. - November 4, 2024) - DLP Resources Inc. (TSXV: DLP) (OTCQB: DLPRF) ("DLP" or the "Company") announces receipt of complete drill results for drillhole A24-020 on the Aurora porphyry copper-molybdenum-silver project in southern Peru. (Figure 1).
Highlights
- Drillhole A24-020 was drilled approximately 135m southeast of A24-016 with the aim of expanding the copper mineralization to the southeast. This drillhole intersected copper-silver and molybdenum mineralization from 3.00m to the end of the hole at 1061.35m. Summary results were as follows:
0.38% CuEq* over 1058.35m from 3.00m to 1061.35m.0.44% CuEq* over 874.35m from 187.00m to 1061.35m.0.76% CuEq* over 339.35m from 722.00m to 1061.35m.0.87% CuEq* over 284.00m from 722.00m to 1006.00m.
The complete set of results for A24-020 are summarized in Table 1 below.
Mr. Gendall, President and CEO, commented: "Drillhole A24-020 has opened up the extension of the copper-molybdenum-silver mineralization to the southeast of Aurora and has yielded very good mineralization from surface to the end depth of 1061.35m. The drillhole was unfortunately stopped in molybdenum mineralization due to the maximum capacity of the drill rig. We have intersected very good copper-molybdenum-silver mineralization in all 20 drillholes drilled to date and we are very encouraged with advancing Aurora to an initial resource estimation by March 2025.
Aurora Cu-Mo Project - Summary of Drill Results for A24-020
Drill hole A24-020 (Figures 2,3,4 and 5) commenced on September 01, 2024 at an inclination of -70 degrees on an azimuth of 285 degrees and ended on October 05, at 1061.35m. Summary geology is as follows:
- 0-3.00m: No core recovered - Overburden.
- 3.00 - 349.00m: Mineralized hornfels.
- 349.00 - 378.40m: Mineralized quartz-eye-feldspar-biotite porphyry.
- 378.40 - 712.75m: Mineralized hornfels.
- 712.75 - 767.35m: Mineralized hornfels and quartz-eye-feldspar-biotite porphyry.
- 767.35 - 1061.35m: Mineralized quartz-eye-feldspar-biotite porphyry.
Table 1. Summary of Drill Results for Diamond Drillhole A24-020. All grades are length-weighted averages of samples within the interval reported.
| Hole | From | To | Interval1 | Description | Cu (total) | Mo | Ag | CuEq* |
| ID | m | m | m | % | % | g/t | % | |
| A24-020 | 3.00 | 1061,35 | 1058.35 | Mineralized hornfels and porphyry | 0.13 | 0.0493 | 1.14 | 0.38 |
| Includes | 187.00 | 1061.35 | 874.35 | Mineralized hornfels and porphyry | 0.14 | 0.0595 | 1.26 | 0.44 |
| Includes | 405.00 | 615.00 | 210.00 | Mineralized hornfels | 0.21 | 0.0092 | 2.54 | 0.27 |
| Includes | 405.00 | 463.00 | 58.00 | Mineralized hornfels | 0.33 | 0.0133 | 4.42 | 0.43 |
| Includes | 722.00 | 1061.35 | 339.35 | Mineralized porphyry with minor intercalated hornfels | 0.10 | 0.1323 | 1.21 | 0.76 |
| Includes | 722.00 | 1006.00 | 284.00 | Mineralized porphyry with minor intercalated hornfels | 0.12 | 0.1473 | 0.81 | 0.87 |
Note: *Copper equivalent grades (CuEq) are for comparative purposes only. Mo, Cu and Ag values are uncut and core recovery is assumed to be
*Copper equivalent calculations use metal prices of Cu - US
1 Intervals are downhole drilled core lengths. Drilling data to date is insufficient to determine true width of mineralization. Mo, Cu and Ag values are uncut.
Table 2: A24-020 Diamond drillhole location, depth, orientation and inclination.
| Hole | Easting | Northing | Elevation | Length | Azimuth | Inclination |
| ID | m | m | m | m | Degrees | Degrees |
| A24-020 | 190,407 | 8,565,914 | 2761 | 1061.35 | 285 | -70 |
Co-ordinates are in WGS84 Zone 19S.
Quality Control and Quality Assurance
DLP Resources Peru S.A.C, a subsidiary of DLP Resources Inc., supervises drilling and carries out sampling of HTW, NTW and BTW core. Logging and sampling are completed at a secured Company facility situated on the project site. Sample intervals are nominally 1m to 3m in length. Drill core is cut in half using a rotary diamond blade saw and samples are sealed on site before transportation to the ALS Peru S.A.C. sample preparation facility in Arequipa by Company vehicles and staff. Prepared samples are sent to Lima by ALS Peru S.A.C. for analysis. ALS Peru S.A.C. is an independent laboratory. Samples are analyzed for 48 elements using a four-acid digestion and ICP-MS analysis (ME-MS61). In addition, sequential copper analyses are done where secondary copper mineralization is observed and reports, soluble copper using sulphuric acid leach, soluble copper in cyanide leach, residual copper and total copper. ALS meets all requirements of International Standards ISO/IEC 17025:2005 and ISO 9001:2015 for analytical procedures.
DLP Resources independently monitors quality control and quality assurance ("QA/QC") through a program that includes the insertion of blind certified reference materials (standards), blanks and pulp duplicate samples. The company is not aware of any drilling, sampling, recovery or other factors that could materially affect the accuracy or reliability of the data for intervals reported in A24-020 from 3.00m to 1061.35m, except for the following intervals from 782.65 to 785.30m and 854.00 to 856.00m, with only 35 to
Aurora Project
Aurora Project is an advanced stage porphyry copper-molybdenum exploration project in the Province of Calca, SE Peru (Figure 1). The Aurora Project was previously permitted for drilling in 2015 but was never executed. Thirteen historical drillholes, drilled in 2001 and 2005 totaling 3,900m were drilled over an area of approximately 1000m by 800m, cut significant intervals of copper and molybdenum mineralization. From logging of the only three remaining holes DDA-01, DDA-3A and DDA-3 and data now available, it appears that only three of the thirteen holes tested the enriched copper zone and only one hole drilled deep enough to test the primary copper and molybdenum zone (see DLP Resources Inc. news release of May 18, 2021).
Salient historic drillhole data of the Aurora Project are:
- 190m @
0.57% Cu,0.008% Mo in DDA-1 with a high-grade intercept of 20m @1.01% Cu related to a supergene enrichment zone of secondary chalcocite; - 142m @
0.5% Cu,0.004% Mo in DDA-3; - 71.7m @
0.7% Cu,0.007% Mo in DDA-3A (see historical Focus Ventures Ltd. news release July 11, 2012); and - One of the historical holes ABC-6 drilled on the edge of the system intersected 78m @
0.45% Cu and0.107% Mo (Figure 2).
A review of the historical drilling indicates that the majority of the thirteen holes were drilled in the leached and partially leached zones of the porphyry system. Ten of the thirteen holes never fully tested the oxide and secondary enrichment zone and/or the primary copper zone at depth encountered in DDA-01. Copper-molybdenum mineralization is hosted by quartz-feldspar porphyries intruded into slates-hornfels and pelitic sandstones belonging to the Ordovician (439 - 463 ma) Sandia Formation.
Figure 1: DLP Project areas in Peru with Aurora Project Shown.
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/6456/228748_e4e9460904db899c_001full.jpg
Figure 2: Aurora Project - Plan view showing historic drilling and drilling by DLP in 2022-2023-2024 with previously reported CuEq* values and A24-020 highlighted in blue.
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/6456/228748_e4e9460904db899c_002full.jpg
Figure 3: Aurora Project - Simplified NW-SE section 1-1' showing DLP and historic drillholes. Mo is on the left and the Cu is within the drillhole column.
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/6456/228748_e4e9460904db899c_003full.jpg
Figure 4: Aurora Project - Plan view showing DLP and historic drillholes with greater than
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/6456/228748_e4e9460904db899c_004full.jpg
Figure 5: Aurora Project -NW-SE section 2-2' showing DLP and historic drillholes. Greater than
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/6456/228748_e4e9460904db899c_005full.jpg
Qualified Person
David L. Pighin, consulting geologist and co-founder of DLP Resources, is the qualified person of the Company as defined by National Instrument 43-101. Mr. Pighin has reviewed and approved the technical contents of this news release.
About DLP Resources Inc.
DLP Resources Inc. is a mineral exploration company operating in Southeastern British Columbia and Peru, exploring for Base Metals and Cobalt. DLP is listed on the TSX-V, trading symbol DLP and on the OTCQB, trading symbol DLPRF. Please refer to our web site www.dlpresourcesinc.com for additional information.
FOR FURTHER INFORMATION PLEASE CONTACT:
DLP RESOURCES INC.
Ian Gendall, CEO & President
Jim Stypula, Executive Chairman
Robin Sudo, Corporate Secretary and Land Manager
Maxwell Reinhart, Investor Relations
Telephone: 250-426-7808
Email: iangendall@dlpresourcesinc.com
Email: jimstypula@dlpresourcesinc.com
Email: robinsudo@dlpresourcesinc.com
Email: maxreinhart@dlpresourcesinc.com
Neither the TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in the policies of the TSX Venture Exchange) accepts responsibility for the adequacy or accuracy of this release.
Cautionary Note Regarding Forward-Looking Information
This release includes certain statements and information that may constitute forward-looking information within the meaning of applicable Canadian securities laws. Forward-looking statements relate to future events or future performance and reflect the expectations or beliefs of management of the Company regarding future events. Generally, forward-looking statements and information can be identified by the use of forward-looking terminology such as "intends" or "anticipates", or variations of such words and phrases or statements that certain actions, events or results "may", "could", "should", "would" or "occur". This information and these statements, referred to herein as "forward‐looking statements", are not historical facts, are made as of the date of this news release and include without limitation, statements regarding discussions of future plans, estimates and forecasts and statements as to management's expectations and intentions with respect to drilling on the Aurora Project in Peru.
These forward‐looking statements involve numerous risks and uncertainties, and actual results might differ materially from results suggested in any forward-looking statements. These risks and uncertainties include, among other things drill results expected from the Aurora Project in Peru.
Although management of the Company has attempted to identify important factors that could cause actual results to differ materially from those contained in forward-looking statements or forward-looking information, there may be other factors that cause results not to be as anticipated, estimated or intended. There can be no assurance that such statements will prove to be accurate, as actual results and future events could differ materially from those anticipated in such statements. Accordingly, readers should not place undue reliance on forward-looking statements and forward-looking information. Readers are cautioned that reliance on such information may not be appropriate for other purposes. The Company does not undertake to update any forward-looking statement, forward-looking information or financial out-look that are incorporated by reference herein, except in accordance with applicable securities laws. We seek safe harbor.
To view the source version of this press release, please visit https://www.newsfilecorp.com/release/228748
FAQ
What are the latest drilling results from DLP Resources (DLPRF) Aurora Project?
When will DLP Resources (DLPRF) complete its initial resource estimation for Aurora?
What was the depth and location of DLP Resources' (DLPRF) latest drill hole A24-020?
