Drilling Underway at Pacific Ridge's Chuchi Copper-Gold Project in B.C.
Pacific Ridge Exploration (TSXV: PEX) (OTCQB: PEXZF) has commenced its inaugural diamond drill program at the Chuchi copper-gold project in B.C. The company plans to drill approximately 3,000 m in five or six drill holes over an 800 m strike length at the BP Zone. Chuchi is located 35 km northwest of Centerra Gold's Mount Milligan mine and is road accessible. Key highlights include:
- Previous drill highlights: 194.0 m at 0.21% Cu and 0.21 g/t Au (CH-90-27), and 229.2 m at 0.10% Cu and 0.61 g/t Au (CH-91-42)
- Pacific Ridge believes Chuchi has significant untested potential for porphyry copper-gold mineralization
- The company has completed geophysical surveys and 3D modelling to guide the current drill program
- Drilling aims to extend known mineralization along strike and at depth
Pacific Ridge Exploration (TSXV: PEX) (OTCQB: PEXZF) ha avviato il suo primo programma di perforazione a diamante presso il progetto Chuchi rame-oro in B.C. L'azienda prevede di edificare circa 3.000 m in cinque o sei fori di perforazione su una lunghezza di 800 m nella zona BP. Chuchi si trova a 35 km a nord-ovest della miniera Mount Milligan di Centerra Gold ed è accessibile su strada. I punti salienti includono:
- Punti salienti delle perforazioni precedenti: 194,0 m a 0,21% Cu e 0,21 g/t Au (CH-90-27), e 229,2 m a 0,10% Cu e 0,61 g/t Au (CH-91-42)
- Pacific Ridge crede che Chuchi abbia un potenziale significativo non testato per la mineralizzazione porfirica rame-oro
- L'azienda ha completato indagini geofisiche e modellazione 3D per guidare il programma di perforazione attuale
- La perforazione mira ad estendere la mineralizzazione conosciuta lungo la lunghezza e in profondità
Pacific Ridge Exploration (TSXV: PEX) (OTCQB: PEXZF) ha comenzado su programa inaugural de perforación con diamante en el proyecto Chuchi de cobre-oro en B.C. La empresa planea perforar aproximadamente 3,000 m en cinco o seis agujeros de perforación a lo largo de una longitud de 800 m en la zona BP. Chuchi se encuentra a 35 km al noroeste de la mina Mount Milligan de Centerra Gold y es accesible por carretera. Los aspectos destacados incluyen:
- Aspectos destacados de perforaciones anteriores: 194,0 m a 0,21% Cu y 0,21 g/t Au (CH-90-27), y 229,2 m a 0,10% Cu y 0,61 g/t Au (CH-91-42)
- Pacific Ridge cree que Chuchi tiene un potencial significativo no probado para la mineralización porfirítica de cobre-oro
- La empresa ha completado estudios geofísicos y modelado 3D para guiar el programa de perforación actual
- La perforación tiene como objetivo extender la mineralización conocida a lo largo de la longitud y a profundidad
퍼시픽 리지 탐사 (TSXV: PEX) (OTCQB: PEXZF)는 B.C.의 추치 구리-금 프로젝트에서 첫 다이아몬드 시추 프로그램을 시작했습니다. 이 회사는 BP 존에서 800m의 스트라이크 길이에 걸쳐 5개 또는 6개의 시추홀에서 약 3,000m를 시추할 계획입니다. 추치는 센테라 골드의 마운트 밀리건 광산에서 북서쪽으로 35km 떨어져 있으며 도로로 접근 가능합니다. 주요 사항은 다음과 같습니다:
- 이전 시추 하이라이트: 194.0m에서 0.21% Cu 및 0.21g/t Au (CH-90-27), 229.2m에서 0.10% Cu 및 0.61g/t Au (CH-91-42)
- 퍼시픽 리지는 추치에 상당한 미검사 구리-금 광체 잠재력이 있다고 믿고 있습니다
- 회사는 현재 시추 프로그램을 안내하기 위해 지구물리 조사와 3D 모델링을 완료했습니다
- 시추는 알려진 광물화를 스트라이크와 깊이에서 확장하는 것을 목표로 합니다
Pacific Ridge Exploration (TSXV: PEX) (OTCQB: PEXZF) a lancé son programme inaugural de forage au diamant sur le projet de cuivre-or Chuchi en Colombie-Britannique. L'entreprise prévoit de forer environ 3 000 m dans cinq ou six trous de forage sur une longueur de 800 m dans la zone BP. Chuchi est situé à 35 km au nord-ouest de la mine Mount Milligan de Centerra Gold et est accessible par la route. Les points clés comprennent :
- Points saillants des forages antérieurs : 194,0 m à 0,21 % Cu et 0,21 g/t Au (CH-90-27), et 229,2 m à 0,10 % Cu et 0,61 g/t Au (CH-91-42)
- Pacific Ridge estime que Chuchi possède un potentiel non testé significatif pour la minéralisation porphyrique cuivre-or
- L'entreprise a complété des enquêtes géophysiques et une modélisation 3D pour guider le programme de forage actuel
- Le forage vise à étendre la minéralisation connue le long de la longueur et en profondeur
Pacific Ridge Exploration (TSXV: PEX) (OTCQB: PEXZF) hat sein erstes Diamantbohrprogramm im Chuchi Kupfer-Gold-Projekt in B.C. gestartet. Das Unternehmen plant, etwa 3.000 m in fünf oder sechs Bohrlöchern über eine Streichenlänge von 800 m in der BP-Zone zu bohren. Chuchi befindet sich 35 km nordwestlich der Mount Milligan Mine von Centerra Gold und ist Straßen zugänglich. Zu den wichtigsten Highlights gehören:
- Frühere Bohr-Highlights: 194,0 m bei 0,21% Cu und 0,21 g/t Au (CH-90-27) sowie 229,2 m bei 0,10% Cu und 0,61 g/t Au (CH-91-42)
- Pacific Ridge glaubt, dass Chuchi erhebliches ungetestetes Potenzial für porphyrische Kupfer-Gold-Mineralisierung hat
- Das Unternehmen hat geophysikalische Untersuchungen und 3D-Modellierungen abgeschlossen, um das aktuelle Bohrprogramm zu leiten
- Die Bohrungen zielen darauf ab, die bekannte Mineralisierung entlang der Strecke und in der Tiefe zu erweitern
- Commencement of inaugural diamond drill program at Chuchi copper-gold project
- Planned 3,000 m drilling program over 800 m strike length at BP Zone
- Road accessibility reduces all-in drilling costs
- Previous drill highlights include significant copper-gold intersections
- Completion of geophysical surveys and 3D modelling to guide current drill program
- Project has remained relatively underexplored for over three decades
- Most historical drilling was shallow with an average vertical depth of 140 m
Vancouver, British Columbia--(Newsfile Corp. - August 20, 2024) - Pacific Ridge Exploration Ltd. (TSXV: PEX) (OTCQB: PEXZF) (FSE: PQWN) ("Pacific Ridge" or the "Company") is pleased to announce that its inaugural diamond drill program at the Chuchi copper-gold project ("Chuchi" or the "Project") has commenced. Chuchi is road accessible and is located 35 km to the northwest of Centerra Gold Inc.'s ("Centerra") Mount Milligan mine in B.C. (see Figure 1).
Highlights:
- Pacific Ridge plans to drill approximately 3,000 m in five or six drill holes over an 800 m strike length at the BP Zone (see Figure 2).
- Chuchi is only a two-hour drive from Fort Saint James and the drill program is completely ground-supported, which significantly reduces the Company's all-in drilling cost.
- The last major drill programs at the Project took place from 1989-1991. Most of the drilling was shallow, average vertical depth of 140 m, and many of the holes ended in mineralization.
- Drill highlights include drill hole CH-90-27 which returned 194.0 m at
0.21% copper ("Cu") and 0.21 g/t gold ("Au") and drill hole CH-91-42 which intersected 229.2 m at0.10% Cu and 0.61 g/t Au (see Table 1).
- Pacific Ridge believes that Chuchi has significant, untested potential for porphyry copper-gold mineralization along its strike length and at depth as many of the historical drill holes were shallow and ended in mineralization.
Quote
"What a wonderful discovery opportunity for shareholders and potential shareholders," said Blaine Monaghan, President and CEO of Pacific Ridge. "I'm unaware of any road accessible copper-gold porphyry projects in B.C. that have returned these kinds of intervals and remained relatively underexplored for more than three decades. Based on our compilation of historical data and exploration work, we are confident that we can extend the known mineralized extents along strike and to depth."
Figure 1: Location of Chuchi and Pacific Ridge's Other Copper-Gold Projects
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/5460/220534_48c53038143e49bb_001full.jpg
Figure 2: Location of BP Zone and Other Targets at Chuchi
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/5460/220534_48c53038143e49bb_002full.jpg
Table 1
Drill Highlights1
Hole No. | From (m) | To (m) | Width (m) | Cu (%) | Au (g/t) | CuEq (%)2 | AuEq (g/t)3 |
CH-89-07 | 38.0 | 138.0 | 100.0 | 0.27 | 0.37 | 0.51 | 0.76 |
Includes | 82.0 | 98.0 | 16.0 | 0.71 | 1.32 | 1.60 | 2.37 |
CH-90-27 | 32.0 | 226.0 | 194.0 | 0.21 | 0.21 | 0.35 | 0.52 |
Includes | 156.0 | 226.0 | 70.0 | 0.31 | 0.34 | 0.54 | 0.80 |
CH-90-30 | 98.0 | 256.0 | 158.0 | 0.22 | 0.10 | 0.29 | 0.43 |
Includes | 182.0 | 256.0 | 74.0 | 0.26 | 0.13 | 0.35 | 0.52 |
CH-90-33 | 54.0 | 304.5 Ɨ | 250.50 | 0.21 | 0.12 | 0.29 | 0.44 |
Includes | 64.0 | 152.0 | 88.0 | 0.36 | 0.21 | 0.51 | 0.75 |
CH-90-37 | 54.3 | 262.1 Ɨ | 207.8 | 0.22 | 0.12 | 0.30 | 0.45 |
Includes | 110.0 | 154.0 | 44.0 | 0.35 | 0.18 | 0.47 | 0.70 |
CH-91-40 | 50.0 | 130.0 | 80.0 | 0.30 | 0.29 | 0.49 | 0.73 |
Includes | 50.0 | 114.0 | 64.0 | 0.35 | 0.33 | 0.57 | 0.85 |
Includes | 64.0 | 104.0 | 40.0 | 0.45 | 0.41 | 0.73 | 1.08 |
CH-91-42 | 91.4 | 320.6 Ɨ | 229.2 | 0.10 | 0.61 | 0.51 | 0.76 |
Includes | 94.0 | 144.0 | 50.0 | 0.09 | 2.10 | 1.50 | 2.23 |
Includes | 94.0 | 122.0 | 28.0 | 0.07 | 3.61 | 2.49 | 3.70 |
And | 200.0 | 242.0 | 42.0 | 0.13 | 0.55 | 0.50 | 0.74 |
CH-19-003 | 91.5 | 411.0 Ɨ | 319.5 | 0.16 | 0.14 | 0.25 | 0.37 |
Includes | 341.0 | 401.0 | 60.0 | 0.26 | 0.24 | 0.42 | 0.63 |
1Sources: Chuchi project historical drilling database; BC Geological Survey (Branch) Assessment Reports 20018 (CH-89-7), 21113 (CH-90-27, CH-90-30, CH-90-33, CH-90-37); Placer Dome Inc. database (CH-91-40, CH-91-42), 39061 (CH-19-003). The Company has not independently validated all historic work, and the reader is cautioned about its accuracy.
2CuEq = ((Cu%) x $Cu x 22.0462) + (Au(g/t) x AuR/CuR x $Au x 0.032151) / ($Cu x 22.0462).
3AuEq = ((Au(g/t) x $Au x 0.032151) + ((Cu%) x CuR/AuR x $Cu x 22.0462) / ($Au x 0.032151).
Commodity prices: $Cu = US
Ɨ End of hole
There has been no metallurgical testing on Chuchi mineralization. The Company estimates copper recoveries (CuR) of
Factors: 22.0462 = Cu% to lbs per tonne and 0.032151 = Au g/t to troy oz per tonne.
Summary of Pacific Ridge's Exploration Work at Chuchi
Since optioning Chuchi from Centerra (see Pacific Ridge news release dated May 9th, 2022), Pacific Ridge has completed a 726 line-km helicopter-borne ZTEM geophysical survey, at 250 m line-spacing covering the entire Project, a 3D inversion model of the ZTEM survey, two Induced Polarization ("IP") survey lines (6.7 line-km) in BP Zone, and 3D inversion modelling of the combined 2015 (Kiska Metals Corporation) and 2023 IP survey lines. The 2D and 3D geophysical inversion models have been compiled to review their relationships in 3D model space and compared against historical geological mapping and drilling results for an updated interpretation of the system geometry and structural controls of copper-gold mineralization in BP Zone. Based on this modelling, the Company believes that there is potential for mineralization to extend to as much as 800 m depth over the kilometre-long central trend of mineralization that follows the North Central Fault and calc-potassic alteration domain
Outside of the BP Zone, Pacific Ridge has completed a reconnaissance surface sampling grid over the eastern half of the Project at 350 m sample spacing, completed mapping and sampling at the Klaw zone and completed 15 line-km of IP survey at Chuchi South (see Figure 2).
2024 Drill Hole Planning
The planned 2024 diamond drilling program at Chuchi will comprise approximately 3,000 m in five or six drill holes in the BP Zone (see Figures 3 and 4). Drill holes will be distributed over a strike length of 800 m across the highly prospective BP Zone and will be collared near the best historical drilling results. These holes are designed to confirm these results and test them to greater depth.
Drilling will also test the interpretation, from the combined 3D geophysical inversion models (ZTEM and IP) and the grade shell model of historical drilling, that BP Zone mineralization forms a tabular shaped body with a high degree of northeast-trending structural control, is steeply northwest-dipping, northeast plunging, and is deep rooted.
Further, drilling will also test for evidence that the BP Zone is structurally segmented with greater preservation potential in downthrown blocks within a north-south trending fault valley on its east side where higher-level porphyry system indicators have been intersected in historical drilling.
Description of the Planned 2024 Drill Holes at Chuchi
Planned #1 (azimuth 081°, inclination -60°, planned length 600 m) is collared on a historical drill trail on the northeastern side of the BP Zone (see Figures 3 and 4), on the northern edge of the calc-potassic domain, and near the transition into the Digger subzone. Drilling will test increasing Cu-Au ratios at depth in drill hole CH-91-42, and if the latter represents a downthrown piece of alkalic lithocap alteration-mineralization. Drill hole CH-91-42 (azimuth 179.3°, inclination -74.2°, length 320.6 m, vertical depth 308.5 m) returned 28 m of
Planned #2 (azimuth 090°, inclination -70°, planned length 600 m) is collared on a historical drill trail near the centre of the BP Zone, within the calc-potassic alteration domain, and near historical drill hole CH-91-40 (azimuth 090°, inclination -59°, length 203.1 m, vertical depth 174.5 m) which returned 40 m at
the centre-to-eastern margin of a steeply west-dipping 550 m E-W x 500 m N-S x 600 m deep stock-shaped conductivity low and magnetic high feature in the 3D ZTEM inversion model (see Figure 6),
a break in chargeability high signature in the 3D IP inversion model thought to be representative of the prospective North Central Fault corridor (see Figure 5),
a resistivity moderate-high gradient zone and moderate deep root feature in the 3D IP model.
Planned #3 (azimuth 088°, inclination -80°, planned length 600 m) is collared on a historical drill trail at the southern side of the BP Zone, within the potassic alteration domain, and in the area of historical drill hole CH-89-07 (azimuth 180°, inclination -46°, length 210.9 m, vertical depth 151.7 m) which returned 16 m at
the southern margin of the steeply west-dipping stock-shaped 3D ZTEM conductivity low and magnetic high feature,
a break in chargeability high signature in the 3D IP inversion model thought to be representative of the 070 Fault corridor,
a moderate-low resistivity domain towards a deep higher resistivity shoulder in the 3D IP inversion model.
Planned #4 (azimuth 090°, inclination -75°, planned length 600 m) is collared on a historical drill trail at the southwestern side of BP Zone, within the calc-potassic alteration domain, and in the area of historical drill hole CH-90-27 (azimuth 265°, inclination -46°, length 304.5 m, vertical depth 219.0 m) which returned 70 m at
Planned #5 (azimuth 300°, inclination -70°, planned length 600 m) is collared on a historical drill trail on the northeastern side of BP Zone, within the calc-potassic alteration domain, and near historical drill hole CH-90-30 (azimuth 278°, inclination -68.5°, length 272.2 m, vertical depth 253.3 m) which returned 74 m at
Planned #6 (azimuth 270°, inclination -75°, planned length 600 m) is collared on a historical drill trail on the northeastern side of the BP Zone, within the calc-potassic alteration domain, and near historical drill hole CH-90-33 (azimuth 273°, inclination -60°, length 304.5 m, vertical depth 263.7 m) which returned 88 m at
the eastern margin of the stock-shaped conductivity low and magnetic high feature in the 3D ZTEM inversion model,
the western margin of deep-rooted chargeability high domain in the 3D IP model and the break in chargeability high signature thought to be representative of the North Central Fault corridor,
a resistivity moderate-high gradient zone and moderate deep root feature in the 3D IP model.
Figure 3: 2024 Drill Plan in BP Zone Showing Aeromagnetic Grid
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/5460/220534_48c53038143e49bb_003full.jpg
Figure 4: 2024 Drill Plan in BP Zone Showing Resistivity Grid
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/5460/220534_48c53038143e49bb_004full.jpg
Figure 5: 2024 Drill Plan in Cross Section Showing 3D IP Chargeability Inversion Model
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/5460/220534_48c53038143e49bb_005full.jpg
Figure 6: 2024 Drill Plan in Cross Section Showing 3D ZTEM Inversion Model
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/5460/220534_48c53038143e49bb_006full.jpg
About Chuchi
Chuchi is over 160 km2 in size and comprises three mineral tenure blocks, Chuchi, under option from Centerra, and Chuchi South and Chuchi West, under option from American Copper Development Corporation (ACDX: TSXV) and a private individual. The Project is road accessible and is located 35 km northwest of Centerra's Mount Milligan mine. Chuchi has seen less than 15,360 metres (89 drill holes) of historical drilling to an average vertical depth of 140 m. Most of this drilling was completed in 1989-1991. The Project hosts several compelling exploration targets within a six-kilometre-long porphyry trend, including the BP Zone. The Company believes that Chuchi has significant untested potential for porphyry copper-gold mineralization at depth as many of the historic drill holes were shallow and ended in mineralization. Further, the porphyry centre has yet to be identified.
About Pacific Ridge
Our goal is to become B.C.'s leading copper-gold exploration company. Pacific Ridge's flagship asset is its
On behalf of the Board of Directors,
"Blaine Monaghan"
Blaine Monaghan
President & CEO
Pacific Ridge Exploration Ltd.
Investor Relations:
Tel: (604) 687-4951
Email: ir@pacificridgeexploration.com
Website: www.pacificridgeexploration.com
LinkedIn: https://www.linkedin.com/company/pacific-ridge-exploration-ltd-pex-/
Twitter: https://twitter.com/PacRidge_PEX
Neither the TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in the policies of the TSX Venture Exchange) accepts responsibility for the adequacy or accuracy of this release.
The technical information contained within this News Release has been reviewed and approved by Danette Schwab, P.Geo., Vice President Exploration, and a Qualified Person as defined by National Instrument 43-101 policy.
Forward-Looking Information: This release includes certain statements that may be deemed "forward-looking statements". All statements in this release, other than statements of historical facts, which address exploration drilling and other activities and events or developments that Pacific Ridge Exploration Ltd. ("Pacific Ridge") expects to occur, are forward-looking statements. Forward looking statements in this news release include the planned 3,000 m drill program at Chuchi. Although Pacific Ridge believes the expectations expressed in such forward-looking statements are based on reasonable assumptions, such statements are not guarantees of future performance and actual results or developments may differ materially from those forward-looking statements. Factors that could cause actual results to differ materially from those in forward looking statements include market prices, exploration successes, and continued availability of capital and financing and general economic, market or business conditions. These statements are based on a number of assumptions including, among other things, assumptions regarding general business and economic conditions, that one of the options will be exercised, the ability of Pacific Ridge and other parties to satisfy stock exchange and other regulatory requirements in a timely manner, the availability of financing for Pacific Ridge's proposed programs on reasonable terms, and the ability of third party service providers to deliver services in a timely manner. Investors are cautioned that any such statements are not guarantees of future performance and actual results or developments may differ materially from those projected in the forward-looking statements. Pacific Ridge does not assume any obligation to update or revise its forward-looking statements, whether because of new information, future events or otherwise, except as required by applicable law.
To view the source version of this press release, please visit https://www.newsfilecorp.com/release/220534
FAQ
What is Pacific Ridge's plan for drilling at the Chuchi copper-gold project?
Where is the Chuchi project located relative to other mines?
What were some notable results from historical drilling at Chuchi?
What is the stock symbol for Pacific Ridge Exploration on the OTCQB?