Myriad Uranium's Drilling at Copper Mountain Continues to Validate Historic Drill Results and Return High Grade Intercepts across the Canning Deposit
Myriad Uranium reports significant uranium mineralization from drilling at the Copper Mountain Uranium Project in Wyoming. Spectral gamma ray logging confirms high-grade uranium at the Canning Deposit area across a 2,500 ft strike length. Notable results include intercepts of 2,530 ppm eU3O8 over 6.56 feet and 1,881 ppm eU3O8 over 8.20 feet. The thirteen holes reported contain 56 intervals greater than 200 ppm eU3O8, with 14 intervals exceeding 500 ppm and 5 intervals above 1,000 ppm. Recent calibration tests suggest earlier reported grades may have been understated by up to 13%. Results are pending chemical assay confirmation.
Myriad Uranium riporta una significativa mineralizzazione di uranio dai sondaggi presso il Copper Mountain Uranium Project nel Wyoming. La registrazione della gamma spettrale conferma uranio di alta qualità nell'area del deposito Canning su una lunghezza di strike di 2.500 piedi. I risultati notevoli includono intercettazioni di 2.530 ppm eU3O8 su 6,56 piedi e 1.881 ppm eU3O8 su 8,20 piedi. I tredici pozzi riportati contengono 56 intervalli superiori a 200 ppm eU3O8, con 14 intervalli che superano i 500 ppm e 5 intervalli oltre 1.000 ppm. I recenti test di calibrazione suggeriscono che i gradi riportati in precedenza potrebbero essere stati sottovalutati fino al 13%. I risultati sono in attesa di conferma analitica chimica.
Myriad Uranium informa sobre una significativa mineralización de uranio a partir de perforaciones en el Copper Mountain Uranium Project en Wyoming. El registro de rayos gamma espectral confirma uranio de alta calidad en el área del depósito Canning a lo largo de una longitud de strike de 2,500 pies. Los resultados destacados incluyen intercepciones de 2,530 ppm eU3O8 sobre 6.56 pies y 1,881 ppm eU3O8 sobre 8.20 pies. Los trece pozos reportados contienen 56 intervalos mayores a 200 ppm eU3O8, con 14 intervalos que superan los 500 ppm y 5 intervalos por encima de 1,000 ppm. Las pruebas de calibración recientes sugieren que los grados reportados anteriormente podrían haber sido subestimados hasta en un 13%. Los resultados están pendientes de la confirmación del análisis químico.
Myriad Uranium는 와이오밍의 Copper Mountain Uranium Project에서 시추 작업을 통해 상당한 우라늄 광물화를 보고합니다. 스펙트럼 감마선 로그가 2,500피트의 스트라이크 길이에 걸쳐 캐닝 광구 지역에서 고급 우라늄을 확인합니다. 주목할 만한 결과로는 2,530 ppm eU3O8가 6.56피트, 1,881 ppm eU3O8가 8.20피트에서 관측되었습니다. 보고된 13개의 구멍에는 200 ppm eU3O8를 초과하는 56개 구간이 포함되어 있으며, 14개 구간은 500 ppm을 초과하고 5개 구간은 1,000 ppm을 초과합니다. 최근의 교정 테스트는 이전에 보고된 등급이 최대 13%까지 과소평가되었을 수 있음을 시사합니다. 결과는 화학 분석 확인을 기다리고 있습니다.
Myriad Uranium rapporte une minéralisation d'uranium significative résultant de forages au Copper Mountain Uranium Project dans le Wyoming. L'enregistrement des rayons gamma spectraux confirme un uranium de haute qualité dans la zone du gisement Canning sur une longueur de 2.500 pieds. Les résultats notables comprennent des interceptions de 2.530 ppm eU3O8 sur 6,56 pieds et 1.881 ppm eU3O8 sur 8,20 pieds. Les treize trous rapportés contiennent 56 intervalles supérieurs à 200 ppm eU3O8, avec 14 intervalles dépassant 500 ppm et 5 intervalles au-dessus de 1.000 ppm. Les récents tests d'étalonnage suggèrent que les grades rapportés précédemment pourraient avoir été sous-estimés jusqu'à 13%. Les résultats sont en attente de confirmation par analyse chimique.
Myriad Uranium berichtet über eine signifikante Uranmineralisierung aus Bohrungen im Copper Mountain Uranium Project in Wyoming. Die spektrale Gamma-Strahlungsprotokollierung bestätigt hochgradiges Uran im Bereich des Canning Deposits über eine Streckenlänge von 2.500 Fuß. Nennenswerte Ergebnisse umfassen Schnittstellen von 2.530 ppm eU3O8 über 6,56 Fuß und 1.881 ppm eU3O8 über 8,20 Fuß. Die dreizehn berichteten Löcher enthalten 56 Intervalle über 200 ppm eU3O8, wobei 14 Intervalle über 500 ppm und 5 Intervalle über 1.000 ppm liegen. Kürzliche Kalibrierungstests legen nahe, dass die zuvor berichteten Grade möglicherweise um bis zu 13% unterschätzt wurden. Die Ergebnisse stehen noch zur Bestätigung der chemischen Analyse aus.
- High-grade uranium mineralization confirmed across 2,500 ft strike length
- Multiple high-grade intercepts including 2,530 ppm eU3O8 over 6.56 feet
- 56 intervals exceeding 200 ppm eU3O8 identified in thirteen holes
- Earlier reported grades potentially understated by 13%
- Results still require confirmation through chemical assays
- Potential radiometric disequilibrium may affect final uranium grades
Vancouver, British Columbia--(Newsfile Corp. - November 14, 2024) - Myriad Uranium Corp. (CSE: M) (OTCQB: MYRUF) (FSE: C3Q) ("Myriad" or the "Company") is pleased to announce further results of equivalent uranium (eU3O8) grades from drilling at the Copper Mountain Uranium Project in Wyoming, USA (Figure 1). Spectral gamma ray logging continues to confirm high-grade uranium mineralisation at the Canning Deposit area and provides strong validation of the historic work done by Union Pacific at Canning and across the Project. These results are still to be confirmed by chemical assay of core and reverse circulation samples being collected from the drilling. Chemical assay results may differ from spectral gamma ray results.
Highlights
Drilling continues to return highly encouraging eU3O8 results from the Canning Deposit area over a strike length of some 2,500 ft (~750 m).
Several intervals reporting average grade greater than 1,000 ppm eU3O8 and peak grade reaching up to 3,870 ppm eU3O8 in borehole CAN0021.
Highlights of significant intervals from the spectral gamma logging include:
CAN0013: 1,881 ppm eU3O8 over 8.20 feet (peak of 2,353 ppm eU3O8 at 305.53 feet)
CAN0013: 1,286 ppm eU3O8 over 6.89 feet (peak of 1,595 ppm eU3O8 at 330.13 feet)
CAN0021: 2,530 ppm eU3O8 over 6.56 feet (peak of 3,870 ppm eU3O8 at 301.60 feet)
CAN0021: 1,714 ppm eU3O8 over 4.26 feet (peak of 2,340 ppm eU3O8 at 330.46 feet)
CAN0023: 1,644 ppm eU3O8 over 8.53 feet (peak of 2,095 ppm eU3O8 at 448.87 feet)
Spectral gamma ray logging results show elevated uranium mineralisation (greater than 200 ppm eU3O8) across multiple intercepts in almost every hole drilled to-date.
The thirteen holes reported here contain 56 intervals over a minimum of 3 feet that are greater than 200 ppm eU3O8, 14 intervals greater than 500 ppm eU3O8, and 5 intervals greater than 1,000 ppm eU3O8.
It is important to note that this initial drill program is focused only on the Canning Deposit area, itself highly significant, but the Project Area also includes six other historical deposits and numerous prospects previously identified by Union Pacific, including Hesitation, Midnight, Knob, Bonanza, Fuller, Mint/Allard, and Kermac/Day, all of which have shown excellent potential through historical drilling and other exploration work.
In addition, our Copper Mountain Project Area includes the formerly-producing Arrowhead and Bonanza uranium mines, which are understood to have produced 0.50 Mlbs at
0.15% U3O8 and 0.78 Mlbs at1.3% U3O8 respectively.CEO Thomas Lamb commented: "Beyond the continuing strong gamma probe results, we are excited about what we are seeing as we log the core and RC chips from Canning in terms of alteration and other characteristics and the deeper understanding that this provides us regarding the deposit and mineralization potential. We are more and more confident that we have validated and gone beyond historical drilling results and limits. I also note that a recent gamma probe calibration test at the US DOE calibration facility in Casper, Wyoming, indicates that the already very strong grades we reported in our first six holes (reported here) may have been understated by as much as
13% . Further comparison will be made with sample assays from an accredited laboratory before any adjustments are made to the reported grade data. Details of this testing are set out below."George van der Walt, Myriad's Qualified Person for the Project and Technical Advisor, commented: "It is encouraging that we continue to find high-grade intercepts in the Canning Deposit area. Most of the intercepts reported previously were concentrated on the eastern side of the Canning Deposit area, whereas the majority of holes in this report are concentrated on the western side of the area, over a strike length of some 2,500 ft (~750 m)."
Significant intervals derived from Spectral Gamma Ray (SGR) logging at 1000 ppm (
| 1000 ppm Cut-off (minimum 3 feet) | Peak Grade eU3O8 (ppm) | ||||||
| Hole ID | From (ft) | To (ft) | Length (ft) | eU3O8 (ppm) | eU3O8 (%) | GT (ft%) | |
| CAN0013 | 302.09 | 310.29 | 8.20 | 1881 | 0.188 | 1.54 | 2353 |
| CAN0013 | 328.33 | 335.22 | 6.89 | 1286 | 0.129 | 0.89 | 1595 |
| CAN0021 | 297.82 | 304.38 | 6.56 | 2530 | 0.253 | 1.66 | 3870 |
| CAN0021 | 328.33 | 332.59 | 4.26 | 1714 | 0.171 | 0.73 | 2340 |
| CAN0023 | 445.42 | 453.95 | 8.53 | 1644 | 0.164 | 1.40 | 2095 |
Notes:
- The interval lengths are "down the hole" and may not represent true width intervals as the exact nature of the mineralisation distribution has not been determined yet. However, most of the holes are being drilled at an inclination of 50 degrees to test a model that indicates steeply dipping mineralisation.
- Intervals were selected over a minimum of 3 feet, with grade below cut-off less than 1 foot being included in the total interval.
- The possible effects of disequilibrium have not been accounted for in the determination of eU3O8 grades.
The boreholes represent a combination of diamond core and reverse circulation drilling that was planned to verify mineralisation identified in drilling by Union Pacific in the late 1970s and to test a grade shell model (above
The majority of the boreholes in this report were drilled on the western side of the high-grade zone of the Canning Deposit area. This demonstrates the presence of high-grade mineralisation across a strike length of at least 2,500 ft (~750 m).
Figure 1: Map of completed boreholes in the Canning Deposit Area.
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/6301/229904_dc384df784b9fb4e_003full.jpg
Equipment and Methods
Drilling is being performed by Harris Exploration using two diamond core (DD) rigs producing HQ (63.5 mm / 2.5 in) core diameter and 96 mm (3.78 in) in hole diameter, and one reverse circulation (RC) rig using a 140 mm (5.5 in) hammer bit. Core samples are being packed into core trays and transported to Riverton for further processing. RC hole runs are being drilled at 5 ft intervals and split on site to produce two representative samples that are then transported to Riverton for further processing. All mineralised intervals will be submitted to ALS Laboratories for chemical analysis to confirm the intervals reported by gamma logging.
Downhole logging is being performed by DGI Geoscience (DGI). A combination of Spectral Gamma Ray (SGR) and Optical Televiewer and/or Acoustic Televiewer is being applied. The probes are manufactured by Mount Sopris Instruments with details as follows:
- QL40 SGR BGO (Sx): Measures the energy of gamma emissions from natural sources within formations crossed by a borehole. It counts the number of gamma emissions at each energy level aiding in lithological determination and correlation. The Probe use a Bismuth Germanium Oxide scintillation crystal.
- QL40 SGR 2G CeBr3 (Sx): Measures the energy of gamma emissions from natural sources within formations crossed by a borehole. It counts the number of gamma emissions at each energy level aiding in lithological determination and correlation. The probe uses a CeBr3 (Cerium Bromide) scintillation crystal.
- QL 40 ABI 2G (At, Gr): Captures high-resolution, oriented images of the borehole wall, allowing the orientation of acoustically visible features to be determined. This includes fractures, bedding/rock fabric, breakouts, bedding planes and other structural features. Contains a built in Natural Gamma sensor that measures the gamma emissions from natural sources in the formation.
- QL OBI 2G (Ot, Gr): Captures a high-resolution, oriented image of the borehole wall using a CMOS digital image sensor, allowing the orientation of features to be determined. This includes fractures, bedding/rock fabric, veins, lithological contacts, etc. Contains a built in Natural Gamma sensor that measures the gamma emissions from natural sources in the formation.
The SGR probes measure the full energy spectrum of the gamma radiation emitted naturally from within the formations crossed by a borehole. A Full Spectrum Analysis (FSA) is performed on the recorded energy spectra. The FSA derives in real time the concentration of the three main radioisotopes 40K, 238U, 212Th, and thus also provides insight into the mineral composition of the formations. DGI is also running optical and acoustic televiewer, when hole conditions allow, to obtain downhole structural information. Borehole paths are being measured using a gyroscopic deviation tool.
Data Verification and Determination of eU3O8 Grades
Initial manufacturer calibration certificates have been provided to Myriad by DGI. Downhole gamma measurements are checked for a repeatability by comparing down and up runs in the borehole. DGI is providing conversion of API units measured by the SGR tools to eU3O8 concentrations using a standard conversion theory and formula.
DGI also ran a calibration test on both the BGO and CeBr3 SGR probes at the Department of Energy (DOE) calibration test facility in Casper, Wyoming on November 1st, 2024. The data indicates that the CeBr3 SGR probe is measuring accurately in the test pit to within
Radiometric Disequilibrium
Radiometric disequilibrium refers to the loss or gain of uranium in the mineralised zone during geologic processes, which can disrupt the equilibrium between the parent isotope and its daughter products. At this stage the effect of disequilibrium has not been fully assessed at Copper Mountain, but it should be noted that geochemical analysis of samples from the drilling could report results for U3O8 that differ from the eU3O8 grades that have been derived from the gamma logging. Some historic reports state that closed can assays from Copper Mountain indicated little disequilibrium, however differences between gamma probe data and were observed. For this reason, the reported eU3O8 values should be considered as preliminary are subject to data verification by chemical assay with appropriate QAQC.
Myriad is in the process of collecting the samples of all the mineralised intervals from drilling and will submit them to a commercial laboratory for full chemical analysis. The results will then be compared to determine the potential effect of disequilibrium, or other factors, on the final uranium grades that will be used in mineral resource estimation when there is sufficient data to allow it.
Geological Background
Uranium mineralisation at Copper Mountain occurs in two distinct geologic environments:
- Fracture-controlled uranium mineralisation hosted in Archaean-aged granite, syenite, isolated occurrences along the margins of diabase dikes and in association with meta-sediment inclusions in granite; and
- As disseminations in coarse-grained sandstones and coatings on cobbles and boulders in the Tertiary-aged Teepee Trail Formation at the Arrowhead (Little Mo) mine and other localities.
Uranium mineralisation is thought to have resulted through supergene and hydrothermal enrichment processes. In both cases, the source of the uranium is thought to be the granites of the Owl Creek Mountains.
Historical Estimates
While Myriad Uranium has determined that the historical estimates described in this news release are relevant to the Copper Mountain Project Area and are reasonably reliable given the authors and circumstances of their preparation, and are suitable for public disclosure, readers are cautioned to not place undue reliance on these historical estimates as an indicator of current mineral resources or mineral reserves at the Project Area. A qualified person (as defined under NI 43-101) has not done sufficient work to classify any of the historical estimates as current mineral resources or mineral reserves, and Myriad Uranium is not treating the historical estimates as a current mineral resource or mineral reserve. Also, while the Copper Mountain Project Area contains all or most of each deposit referred to, some of the resources referred to may be located outside the current Copper Mountain Project Area. Furthermore, the estimates are decades old and based on drilling data for which the logs are, as of yet, predominantly unavailable. The historical resource estimates, therefore, should not be unduly relied upon.
Inherent limitations of the historical estimates include that the nature of the mineralisation (fracture hosted) makes estimation from drill data less reliable than other deposit types (e.g. those that are thick and uniform). From Myriad Uranium's viewpoint, limitations include that the Company has not been able to verify the data itself and that the estimate may be optimistic relative to subsequent work which applied a "delayed fission neutron" (DFN) factor to calculate grades. On the other hand, DFN is controversial, in that the approach is viewed by some experts as too conservative. Nevertheless, it was applied in later resource estimations by Union Pacific relating to Copper Mountain.
To verify the historical estimates and potentially re-state them as current resources, a program of digitization of available data would be required. This must be followed by re-logging and/or re-drilling to generate new data to the extent necessary that it is comparable with the original data, or new data that can be used to establish the correlation and continuity of geology and grades between boreholes with sufficient confidence to estimate mineral resources.
Qualified Person
The scientific or technical information in this news release respecting the Company's Copper Mountain Project has been approved by George van der Walt, MSc., Pr.Sci.Nat., FGSSA, a Qualified Person as defined in National Instrument 43-101 - Standards of Disclosure for Mineral Projects. Mr van der Walt is employed by The MSA Group (Pty) Ltd (MSA), a leading geological consultancy providing services to the minerals industry, based in Johannesburg, South Africa. He has more than 20 years industry experience and sufficient relevant experience in the type and style of mineralisation to report on exploration results.
The information and interpretations thereof are based on the Qualified Person's initial review of historical reports, which were recently obtained by the Company. The information did not include original data such as drilling records, sampling, analytical or test data underlying the information or opinions contained in the written documents. Therefore, the Qualified Person has not reviewed or otherwise verified the information and has not done sufficient work to classify the historical estimates as current mineral resources or mineral reserves. The Qualified Person considers the information to be relevant based on the amount and quality of work undertaken and reported historically. A more thorough review of any available original data will be undertaken and reported on in more detail in future releases.
About Myriad Uranium Corp.
Myriad Uranium Corp. is a uranium exploration company with an earnable
Myriad also has a
Myriad Contacts:
Thomas Lamb
President and CEO
tlamb@myriaduranium.com
Forward-Looking Statements
This news release contains "forward-looking information" that is based on the Company's current expectations, estimates, forecasts and projections. This forward-looking information includes, among other things, the Company's business, plans, outlook and business strategy. The words "may", "would", "could", "should", "will", "likely", "expect," "anticipate," "intend", "estimate", "plan", "forecast", "project" and "believe" or other similar words and phrases are intended to identify forward-looking information. The reader is cautioned that assumptions used in the preparation of any forward-looking information may prove to be incorrect, including with respect to the Company's business plans respecting the exploration and development of the Company's mineral properties, the proposed work program on the Company's mineral properties and the potential and economic viability of the Company's mineral properties. Forward-looking information is subject to known and unknown risks, uncertainties and other factors that may cause the Company's actual results, level of activity, performance or achievements to be materially different from those expressed or implied by such forward-looking information. Such factors include, but are not limited to: changes in economic conditions or financial markets; increases in costs; litigation; legislative, environmental and other judicial, regulatory, political and competitive developments; and technological or operational difficulties. This list is not exhaustive of the factors that may affect our forward-looking information. These and other factors should be considered carefully, and readers should not place undue reliance on such forward-looking information. The Company does not intend, and expressly disclaims any intention or obligation to, update or revise any forward-looking information whether as a result of new information, future events or otherwise, except as required by applicable law.
The CSE has not reviewed, approved or disapproved the contents of this news release.
APPENDIX 1: Equivalent uranium (eU3O8) intervals at 500 ppm and 200 ppm cut-off (over 3 ft minimum)
| 500 ppm Cut-off (minimum 3 feet) | ||||||
| Hole ID | From (ft) | To (ft) | Length (ft) | eU3O8 (ppm) | eU3O8 (%) | GT (ft%) |
| CAN0011 | 386.71 | 391.63 | 4.92 | 877 | 0.088 | 0.43 |
| CAN0012 | 328.33 | 335.87 | 7.54 | 718 | 0.072 | 0.54 |
| CAN0013 | 290.94 | 310.94 | 20.01 | 1251 | 0.125 | 2.50 |
| CAN0013 | 321.11 | 337.18 | 16.07 | 950 | 0.095 | 1.53 |
| CAN0014 | 568.42 | 574.33 | 5.90 | 960 | 0.096 | 0.57 |
| CAN0019 | 267.65 | 277.16 | 9.51 | 668 | 0.067 | 0.64 |
| CAN0019 | 292.25 | 301.43 | 9.18 | 629 | 0.063 | 0.58 |
| CAN0019 | 583.18 | 588.43 | 5.25 | 712 | 0.071 | 0.37 |
| CAN0020 | 439.85 | 448.38 | 8.53 | 910 | 0.091 | 0.78 |
| CAN0021 | 297.17 | 307.99 | 10.82 | 1789 | 0.179 | 1.94 |
| CAN0021 | 327.02 | 333.25 | 6.23 | 1395 | 0.139 | 0.87 |
| CAN0023 | 317.50 | 320.78 | 3.28 | 760 | 0.076 | 0.25 |
| CAN0023 | 370.31 | 374.25 | 3.94 | 664 | 0.066 | 0.26 |
| CAN0023 | 443.13 | 457.23 | 14.10 | 1269 | 0.127 | 1.79 |
| 200 ppm Cut-off (minimum 3 feet) | ||||||
| Hole ID | From (ft) | To (ft) | Length (ft) | eU3O8 (ppm) | eU3O8 (%) | GT (ft%) |
| CAN0011 | 201.39 | 211.23 | 9.84 | 323 | 0.032 | 0.32 |
| CAN0011 | 211.89 | 217.46 | 5.58 | 360 | 0.036 | 0.20 |
| CAN0011 | 228.29 | 247.97 | 19.68 | 317 | 0.032 | 0.62 |
| CAN0011 | 249.28 | 257.48 | 8.20 | 307 | 0.031 | 0.25 |
| CAN0011 | 263.71 | 274.21 | 10.50 | 290 | 0.029 | 0.30 |
| CAN0011 | 289.95 | 304.06 | 14.10 | 328 | 0.033 | 0.46 |
| CAN0011 | 318.16 | 331.94 | 13.78 | 270 | 0.027 | 0.37 |
| CAN0011 | 338.50 | 342.43 | 3.94 | 258 | 0.026 | 0.10 |
| CAN0011 | 357.19 | 363.10 | 5.90 | 287 | 0.029 | 0.17 |
| CAN0011 | 370.97 | 376.87 | 5.90 | 246 | 0.025 | 0.15 |
| CAN0011 | 385.40 | 393.27 | 7.87 | 674 | 0.067 | 0.53 |
| CAN0012 | 323.74 | 340.14 | 16.40 | 513 | 0.051 | 0.84 |
| CAN0012 | 344.73 | 349.65 | 4.92 | 262 | 0.026 | 0.13 |
| CAN0012 | 423.45 | 429.35 | 5.90 | 431 | 0.043 | 0.25 |
| CAN0012 | 464.12 | 470.35 | 6.23 | 258 | 0.026 | 0.16 |
| CAN0013 | 287.98 | 312.26 | 24.27 | 1086 | 0.109 | 2.64 |
| CAN0013 | 316.19 | 339.81 | 23.62 | 811 | 0.081 | 1.91 |
| CAN0013 | 620.25 | 627.79 | 7.54 | 271 | 0.027 | 0.20 |
| CAN0014 | 422.14 | 425.42 | 3.28 | 264 | 0.026 | 0.09 |
| CAN0014 | 538.58 | 541.86 | 3.28 | 312 | 0.031 | 0.10 |
| CAN0014 | 550.38 | 553.66 | 3.28 | 256 | 0.026 | 0.08 |
| CAN0014 | 555.30 | 576.62 | 21.32 | 595 | 0.060 | 1.27 |
| CAN0014 | 582.53 | 587.78 | 5.25 | 222 | 0.022 | 0.12 |
| CAN0014 | 589.74 | 594.01 | 4.26 | 212 | 0.021 | 0.09 |
| CAN0014 | 596.63 | 615.00 | 18.37 | 230 | 0.023 | 0.42 |
| CAN0015 | 166.62 | 181.71 | 15.09 | 359 | 0.036 | 0.54 |
| CAN0015 | 190.24 | 213.86 | 23.62 | 300 | 0.030 | 0.71 |
| CAN0015 | 215.50 | 226.32 | 10.82 | 286 | 0.029 | 0.31 |
| CAN0015 | 232.22 | 250.92 | 18.70 | 274 | 0.027 | 0.51 |
| CAN0015 | 254.20 | 261.42 | 7.22 | 257 | 0.026 | 0.19 |
| CAN0015 | 265.02 | 268.96 | 3.94 | 284 | 0.028 | 0.11 |
| CAN0015 | 270.60 | 278.14 | 7.54 | 249 | 0.025 | 0.19 |
| CAN0015 | 676.01 | 679.29 | 3.28 | 242 | 0.024 | 0.08 |
| CAN0015 | 717.66 | 722.58 | 4.92 | 345 | 0.034 | 0.17 |
| CAN0016 | 525.46 | 534.31 | 8.86 | 367 | 0.037 | 0.33 |
| CAN0017 | No intervals with eU3O8 greater than 200 ppm | |||||
| CAN0018 | 269.29 | 273.55 | 4.26 | 451 | 0.045 | 0.19 |
| CAN0019 | 217.14 | 231.24 | 14.10 | 359 | 0.036 | 0.51 |
| CAN0019 | 232.55 | 279.13 | 46.58 | 373 | 0.037 | 1.74 |
| CAN0019 | 287.98 | 304.06 | 16.07 | 482 | 0.048 | 0.77 |
| CAN0019 | 310.62 | 329.31 | 18.70 | 293 | 0.029 | 0.55 |
| CAN0019 | 582.20 | 590.73 | 8.53 | 556 | 0.056 | 0.47 |
| CAN0020 | 438.54 | 449.36 | 10.82 | 787 | 0.079 | 0.85 |
| CAN0020 | 485.77 | 490.69 | 4.92 | 281 | 0.028 | 0.14 |
| CAN0020 | 517.58 | 520.86 | 3.28 | 211 | 0.021 | 0.07 |
| CAN0021 | 128.25 | 131.86 | 3.61 | 389 | 0.039 | 0.14 |
| CAN0021 | 296.18 | 309.63 | 13.45 | 1507 | 0.151 | 2.03 |
| CAN0021 | 325.05 | 334.23 | 9.18 | 1057 | 0.106 | 0.97 |
| CAN0022 | 482.16 | 486.75 | 4.59 | 427 | 0.043 | 0.20 |
| CAN0022 | 702.90 | 707.50 | 4.59 | 257 | 0.026 | 0.12 |
| CAN0023 | 310.94 | 322.10 | 11.15 | 442 | 0.044 | 0.49 |
| CAN0023 | 334.89 | 344.73 | 9.84 | 320 | 0.032 | 0.31 |
| CAN0023 | 356.54 | 362.44 | 5.90 | 287 | 0.029 | 0.17 |
| CAN0023 | 368.67 | 375.23 | 6.56 | 541 | 0.054 | 0.35 |
| CAN0023 | 441.82 | 461.50 | 19.68 | 990 | 0.099 | 1.95 |
| CAN0023 | 547.10 | 550.38 | 3.28 | 440 | 0.044 | 0.14 |
APPENDIX 1: Table of drilled positions
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/6301/229904_dc384df784b9fb4e_006full.jpg
To view the source version of this press release, please visit https://www.newsfilecorp.com/release/229904
FAQ
What are the latest drilling results from Myriad Uranium (MYRUF) at Copper Mountain?
How many significant uranium intervals did Myriad Uranium (MYRUF) identify in their recent drilling?
What was the highest grade uranium intercept in Myriad's (MYRUF) recent Copper Mountain drilling?
